Free toolbox talks

Toolbox talks your crew will actually listen to

Written by a working superintendent for electrical and construction crews. Each talk reads aloud in under five minutes and comes with key points, two questions for the crew, a check you can walk today, the rule it comes from, and a sign-in sheet. Here are 12 to read right now, and every 52-week talk pack is free: pick your trade and we'll email it to you.

12 free 52-week trade packs
52 longer Leader's Talks
<5 min to read aloud
1 sign-in sheet with every talk

12 free talks

Pick one for tomorrow morning

Open a talk to read it, then print it with its sign-in sheet. Every rule cited links to the official source.

ElectricalJanuary sample

GFCI: Know What's Protecting You

A GFCI can trip faster than you can let go. But only if it's there and working. Let's check ours.

Read the talk

This week's Leader's Talk is about ground-fault protection, the device that has probably saved more electricians and tradespeople from serious shock than any other piece of equipment on a jobsite.

A ground-fault circuit interrupter watches the current going out on the hot conductor and coming back on the neutral. If those don't match, some of the current is going somewhere it shouldn't, maybe through a person to ground. OSHA defines a GFCI as a device intended for the protection of personnel that de-energizes a circuit within an established period of time when current to ground exceeds a predetermined value. That value is lower than what it takes to trip the regular breaker. In plain words, a breaker protects the wire. A GFCI protects you.

Now the rule. In construction, the employer has to protect employees with either GFCIs or an assured equipment grounding conductor program. Under the GFCI option, all 120-volt, single-phase, 15- and 20-ampere receptacle outlets that are not part of the permanent wiring of the building and that are in use by employees must have GFCI protection. There's a narrow exception for receptacles on a two-wire, single-phase portable or vehicle-mounted generator rated not more than 5 kW, where the circuit conductors are insulated from the generator frame and all other grounded surfaces. Don't assume a generator fits that exception. Check it.

What does that mean on our jobs? Temporary power, spider boxes, and cord sets plugged into non-permanent receptacles need GFCI protection or a working assured grounding program. In a building where the permanent wiring isn't done yet, or in a live facility where you're plugging into temporary power, know which one you're using.

Testing matters. OSHA's construction electrical eTool says to test GFCIs according to the manufacturer's recommended procedure. A GFCI that's been knocked around, frozen, or wet might not work. Pressing the test button and confirming it trips takes seconds.

A GFCI that trips repeatedly is telling you something. It could be a damaged cord, a wet connector, or a bad tool. Don't swap it for a plain receptacle or keep resetting it until it holds. Find the cause.

Leader notes: Walk the temporary power on your area this week. Find every non-permanent 120-volt receptacle the crew is using and confirm it's GFCI protected or covered by the assured grounding program. Have the crew test the GFCIs at the start of shift per the manufacturer. Treat a nuisance trip as a hazard report, not an annoyance. Follow your site's temporary power procedure.

Key points

  • A GFCI de-energizes the circuit when current leaks to ground
  • 120-volt, single-phase, 15- and 20-amp non-permanent receptacles need GFCI protection or an assured grounding program
  • A narrow exception exists for certain small generators; verify it applies
  • Test GFCIs per the manufacturer's procedure
  • Repeated trips mean a hazard: find the cause

Ask the crew

  1. Which receptacles are we using today, and what protects each one?
  2. What should happen when a GFCI keeps tripping?

Check it today

Every non-permanent 120-volt receptacle the crew is using today has been confirmed GFCI protected and tested.

Where this comes from

Get all 12 talk packs free
Want a full year of talks like this? The 52-week packs are free. Running a crew? The Foreman Membership adds all 108 one-page trackers and the Foreman training track for $19 a month.
ElectricalFebruary sample

Dead First: The Electrically Safe Work Condition

The safest energized work is the work we never do energized. February starts with turning it off.

Read the talk

February is our electrical safety deep dive, and this week's Leader's Talk starts where every electrical safety program starts: turn it off.

OSHA's general industry electrical work practice rule, which applies in a lot of the facilities we work in, says live parts that an employee may be exposed to shall be de-energized before the employee works on or near them. There are only two reasons the rule accepts for leaving them energized. One is that de-energizing would create additional or increased hazards, and OSHA's example is interrupting life support equipment. The other is that de-energizing is not feasible because of the design of the equipment or operational limits. "It's inconvenient" and "the customer doesn't want an outage" are not on that list.

NFPA 70E, the consensus standard most electrical safety programs are built on, uses the idea of an electrically safe work condition. The concept is simple: the equipment is disconnected from every source, locked and tagged, verified with proper testing to be de-energized, and grounded where that's needed. Only then is it treated as safe to work on. Until all of that is done, it's treated as energized.

OSHA's rule lines up with that. Control circuit devices like push buttons, selector switches, and interlocks can't be the only way you de-energize equipment. A lock and a tag go on each disconnecting means. Stored electrical energy, like capacitors, is released. And a qualified person tests to verify the parts are actually de-energized before anyone touches them.

Why does this matter so much on our work? Data centers, hospitals, plants, and occupied commercial buildings all carry pressure to keep things running. That pressure shows up as "can you just do it hot?" The answer starts with the rule: de-energize unless one of those two conditions really applies, and if energized work really is justified, it gets a formal plan, the right qualified people, and the right protective equipment. We'll cover energized work permits next week.

For anyone who isn't qualified for electrical work: your job is to stay out of spaces with exposed energized parts and to respect locks, tags, barricades, and signs.

Leader notes: For every electrical task on this week's schedule, ask one question in the pre-task plan: "Why can't this be done de-energized?" If the answer isn't one of the two reasons in the rule, plan the outage. Make sure locks, tags, and test instruments are on site before the work starts, not after. Back up your electricians when they push back on working hot. Follow your site's electrical safety program and lockout procedure.

Key points

  • Live parts are de-energized before work unless it creates greater hazards or is infeasible
  • Inconvenience is not a reason to work energized
  • Push buttons and interlocks are not the sole means of de-energizing
  • Lock and tag every disconnect, release stored energy, and test
  • Treat it as energized until verified de-energized

Ask the crew

  1. What jobs this month are we being asked to do hot, and why?
  2. Who on this crew is qualified to verify de-energized conditions?

Check it today

Every electrical task on this week's schedule has a written reason on the pre-task plan if it will not be done de-energized.

Where this comes from

Get all 12 talk packs free
Want a full year of talks like this? The 52-week packs are free. Running a crew? The Foreman Membership adds all 108 one-page trackers and the Foreman training track for $19 a month.
Ladders & LiftsMarch sample

Pick the Right Way Up

New month, new altitude: March is ladders, scaffolds and lifts. Start by picking the right way up.

Read the talk

Welcome to March. For the next few weeks we are talking about getting up off the floor and getting back down in one piece: ladders, scaffolds, scissor lifts and boom lifts. Most of us climb something every single day, which is exactly why we stop thinking about it.

Here is where it starts. The rule says that wherever there is a break in elevation of 19 inches or more at a point where people get on and off, you need a stairway or a ladder, unless there is a ramp, runway, sloped embankment or personnel hoist. That covers a lot more spots than people think: the edge of an equipment pad, a housekeeping pad in an electrical room, a loading dock, the back of a trailer. If somebody is hopping up and down off it all day, it needs a real way up.

The bigger question is which tool fits the task. A stepladder is great for a quick device swap. It is the wrong choice for two hours of pulling wire through a cable tray at full reach. If you find yourself on a ladder leaning, stretching, or climbing up and down every five minutes for material, that is the job telling you it wants a scaffold or a lift. The cost of bringing in the right equipment is small next to the cost of somebody hurt.

Think about it in three questions. How long am I up there? How far do I need to reach? What am I carrying? Short time, close reach, light hands: ladder. Longer time, wider reach, material and tools: scaffold or lift. Overhead hazards, energized equipment nearby, or a live facility floor: talk to the foreman before anything rolls in.

Also remember the rule requires that stairways and ladder fall protection be in place before people start the work that needs them. Access is not something we fix later in the week.

Over this month we will dig into inspection, setup, the scaffold tag, lift controls, wind, power lines and rescue. Some days will be quick quizzes. Bring your questions and your stories.

Leader notes: Walk the area before this talk and point to one real access point that is 19 inches or higher. Ask the crew to name the access method for today's tasks out loud. If anyone says "I just climb up the conduit rack," fix that today. Follow your site's procedure for selecting and requesting lifts and scaffolds.

Key points

  • A break in elevation of 19 inches or more at an access point needs a stairway or ladder
  • Match the equipment to time aloft, reach, and what you carry
  • Constant leaning or trips for material means you need a scaffold or lift
  • Access and its fall protection go in before the work starts

Ask the crew

  1. Where on this job are people stepping up or down 19 inches or more without a real access point?
  2. Which task this week should move from a ladder to a scaffold or lift?

Check it today

Every access point with a 19-inch or greater break in elevation has a stairway, ladder, ramp or other listed access in place.

Where this comes from

Get all 12 talk packs free
Want a full year of talks like this? The 52-week packs are free. Running a crew? The Foreman Membership adds all 108 one-page trackers and the Foreman training track for $19 a month.
Leadership & CultureApril sample

Making the Silica Plan Real

Every site has a written silica plan. Today's question: does the crew's work actually match it?

Read the talk

Every employer covered by the construction silica standard has to have a written exposure control plan. Many of us have never read ours. Today we fix that.

The standard says the plan describes the tasks that involve exposure to respirable crystalline silica; the engineering controls, work practices and respiratory protection used for each task; the housekeeping measures; and the procedures used to restrict access to work areas, when needed, to minimize the number of people exposed. The plan is reviewed at least annually and updated as necessary.

Then the competent person makes frequent and regular inspections to implement it. That person is designated by the employer, can identify silica hazards, and has the authority to correct them.

Here is where foremen come in. A plan that says "rotary hammers with shroud and HEPA dust collector" means nothing if the crew is drilling without the vacuum because the hose is in the other truck.

Three things to check this week.

First, match the work to the plan. List the silica tasks your crew is doing: drilling, coring, saw cutting, chipping, grinding. Find each one in the plan. If a task is not in there, the plan needs an update before the task continues.

Second, watch the combined time. Table 1 has different respirator columns for tasks lasting four hours or less and more than four hours per shift. The standard says that when an employee does more than one Table 1 task in a shift and the total combined duration is more than four hours, the requirements for more than four hours apply to each task. A morning of chipping and an afternoon of saw cutting can push someone into the bigger column.

Third, think about access. If the plan calls for restricting access near cutting, are other trades kept back?

Indoors, Table 1 also says that tasks in enclosed areas need exhaust as needed to minimize the build-up of visible airborne dust. A closed electrical room or a stairwell can fill with dust fast.

Leader notes: Bring the written exposure control plan to the talk. Read out the sections for the two silica tasks your crew does most. Ask the crew whether the field matches the paper. Track total time on Table 1 tasks for anyone doing several in one shift. Report any gaps to the competent person and follow your site's procedure for updating the plan.

Key points

  • The written plan lists tasks, controls, housekeeping and access limits
  • The plan is reviewed at least annually
  • Combined Table 1 tasks over 4 hours use the over-4-hour column
  • Enclosed areas need exhaust to limit visible dust
  • Field work must match the plan

Ask the crew

  1. Is every silica task we did this week in the written plan?
  2. Who on this crew does more than four hours of silica tasks in a shift?

Check it today

Every silica task the crew is doing today appears in the written exposure control plan, with its listed control in use.

Where this comes from

Get all 12 talk packs free
Want a full year of talks like this? The 52-week packs are free. Running a crew? The Foreman Membership adds all 108 one-page trackers and the Foreman training track for $19 a month.
FallsMay sample

The 6-Foot Rule and Where It Applies

Six feet is the line. Today's Leader's Talk: where the construction fall rule applies on our jobs.

Read the talk

This month is about falls, and the starting point is simple. Under the federal construction rule, each worker on a walking or working surface with an unprotected side or edge that is 6 feet or more above a lower level must be protected by a guardrail system, a safety net system or a personal fall arrest system.

That same 6-foot line shows up across the rule. It covers people building a leading edge, people working near a leading edge, holes in floors and roofs, steep roofs, residential construction, and any other walking or working surface the rule does not address separately.

Pay attention to what counts as a lower level. The definition is any area or surface you could fall to: the ground, a floor, a platform, a ramp, an excavation, a tank, water or equipment. That means you measure to whatever you would land on, not just the slab. A 4-foot mezzanine over a 3-foot pit is a different conversation than it looks.

Also know what this rule does not cover. Scaffolds, ladders and aerial lifts have their own requirements, which we covered in March. If you are on one of those, follow those rules and your site procedure.

On our jobs, falls show up in places people do not expect. Electrical rooms with open equipment pits. Data center roofs with mechanical units and conduit runs. Prefab racks loaded on a flatbed. Residential second floors before the stairs and rails go in. Industrial mezzanines with a missing gate.

The rule lists the options. Your site's fall protection plan and competent person choose which one fits. Many sites prefer passive protection like guardrails first, because a rail protects everybody without anyone having to clip in. Personal fall arrest works, but only if it is the right gear, inspected, anchored correctly and rigged so you do not hit the level below.

This week, we will get into harnesses, anchors, clearance and rescue. Bring your questions.

Leader notes: Before this talk, walk the work area and list every spot where someone could be 6 feet or more above a lower level. Name the protection for each one and who owns it today. Ask the crew to add anything you missed. Write the exposures and controls into today's pre-task plan, and follow your site's fall protection procedure where it is stricter than the minimum.

Key points

  • Unprotected sides and edges 6 feet or more above a lower level need guardrails, nets or personal fall arrest
  • Lower level means anything you could land on, including pits, tanks and equipment
  • Scaffolds, ladders and lifts have their own rules
  • The site plan and competent person pick the protection for each exposure

Ask the crew

  1. Where on this job could someone be 6 feet above a lower level without realizing it?
  2. Which of our exposures could be protected with a rail instead of a harness?

Check it today

Every exposure of 6 feet or more in today's work area has a named protection method written on the pre-task plan.

Where this comes from

Get all 12 talk packs free
Want a full year of talks like this? The 52-week packs are free. Running a crew? The Foreman Membership adds all 108 one-page trackers and the Foreman training track for $19 a month.
Heat & ColdJune sample

Building the Crew's Heat Plan

Heat illness is preventable with a plan. Today's Leader's Talk: build one for your crew this week.

Read the talk

We have covered water, rest, shade, acclimatization and warning signs. Today is about pulling it into a plan the whole crew can follow.

Start with the schedule. NIOSH recommends shortening work periods and lengthening rest periods as temperature, humidity and sunshine increase, when there is no air movement, when protective clothing or equipment is worn, and for heavier work. In practice, many crews move the heaviest work, like pulling feeder, setting gear or digging, to the cooler part of the day where the schedule allows. And yes, the project manager may need to hear that the cable pull starts at first light. They will survive.

Next, water and shade. Cool water close to the work, enough for the crew and the whole shift, with individual cups. A shaded or cool rest area close by.

Then people. Identify new workers and workers returning from time off, and put them on a reduced exposure schedule. NIOSH recommends training both workers and supervisors before hot work starts, and closely supervising new employees for the first 14 days or until they are acclimatized. Pair people up with a buddy.

Then the emergency plan. Who calls 911? Where is the ice or cold water for rapid cooling? Can responders find you? The first aid rule says that where 911 is available, the employer must make sure the communication system works, and if the area does not automatically give the caller's location to dispatch, the site's latitude and longitude or other clear location information must be posted. On a big campus or a live data center with secured gates, plan who meets the ambulance and how they get through security.

Last, check during the day. Walk the job during peak heat. Look at faces, ask questions, and send people to break before they need it.

Keep it simple enough to use. A heat plan that lives in a binder in the trailer does nothing. A heat plan that the crew can recite at the morning huddle saves people.

Leader notes: Write today's heat controls into the pre-task plan: schedule, water location, rest area, new workers and their buddies, and the emergency contact and location. Check the forecast every morning this month. Make it clear that anyone can call a break for heat without getting grief. Follow your employer's heat illness prevention program, which may be stricter than what we covered here.

Key points

  • Shorten work periods and lengthen rest as heat, humidity, sun and workload increase
  • Cool water and a cool rest area close to the work
  • Reduced exposure plans and buddies for new and returning workers
  • Emergency plan: who calls, how to cool, how responders find you
  • Walk the job at peak heat

Ask the crew

  1. What heavy work this week could move to a cooler time of day?
  2. If someone went down from heat right now, how would responders find us?

Check it today

Today's pre-task plan lists the water location, rest area, buddy pairs, new workers' schedules and the emergency contact and site location.

Where this comes from

Get all 12 talk packs free
Want a full year of talks like this? The 52-week packs are free. Running a crew? The Foreman Membership adds all 108 one-page trackers and the Foreman training track for $19 a month.
Excavation & Confined SpaceJuly sample

Digging Near the Marks

Leader's Talk: the marks tell you roughly where it is. Exposing it safely is still on us. Here's how.

Read the talk

Last week we talked about getting locates before we dig. This week is about what happens when the bucket gets close to those marks, which is where most of the damage happens.

The rule says that when excavation operations approach the estimated location of underground installations, the exact location has to be determined by safe and acceptable means. A paint mark is an estimate. The line could be off to either side or deeper or shallower than you expect. So the closer you get, the gentler the method.

What does that look like on our jobs? The machine stops short of the marks and hand digging or vacuum excavation takes over to expose the line. Shovels go in vertically and carefully, not as a pry bar. Somebody watches the spot, not just the operator. And when you find the line, you confirm it matches the marks. If it does not, stop and call.

The rule also says that while the excavation is open, underground installations have to be protected, supported or removed as necessary to safeguard employees. A gas line hanging across a trench needs support. A duct bank undermined by your trench needs a plan before the dirt under it is gone.

For electrical crews, there is a second rule to think about. Before work begins, the employer has to find out, by asking, looking, or by instruments, whether any part of an energized electric power circuit, exposed or concealed, is located so that the work could bring a person, tool or machine into contact with it. On a live data center or hospital campus, the most dangerous thing in the ground may be our own feeder from last year.

One more habit: when a line is exposed, leave it visible and flagged until it is protected or backfilled, so the next shift does not rediscover it with a shovel.

Here is the mindset. Marks narrow down where to be careful. They do not tell you where it is safe to dig fast.

Leader notes: Walk the dig with the crew and point to each mark. Ask who is hand digging, how far from the marks the machine stops, and who is spotting. Compare the marks to as-built drawings for the campus. If anything does not line up, stop and resolve it before work starts. Follow your site's procedure and the facility's requirements for excavation near energized services.

Key points

  • Paint marks are estimates; find the exact location by safe means as you approach
  • Switch to hand or vacuum digging near the marks
  • Support or protect exposed utilities while the trench is open
  • Find energized circuits, exposed or concealed, before work begins

Ask the crew

  1. How close to the marks does our machine stop on this job?
  2. What would you do if you uncovered a line that is not on the marks or drawings?

Check it today

A spotter and hand or vacuum digging are in use wherever the dig approaches a utility mark today.

Where this comes from

Get all 12 talk packs free
Want a full year of talks like this? The 52-week packs are free. Running a crew? The Foreman Membership adds all 108 one-page trackers and the Foreman training track for $19 a month.
Tools & EquipmentAugust sample

Grinders Spin Faster Than You Think

Leader's Talk: a cracked wheel at full speed can come apart without warning. Ring test, rating, guard.

Read the talk

This week's Leader's Talk is about abrasive wheels and grinders. We use them to cut strut and all-thread, clean up cut ends, and notch steel. A grinding wheel spins fast and can break apart, and when it does, the pieces leave at high speed.

Start with the wheel. The rule says all abrasive wheels shall be closely inspected and ring-tested before mounting to ensure they are free from cracks or defects. OSHA's tool booklet explains the ring test: tap the wheel gently with a light non-metallic instrument. A stable and undamaged wheel gives a clear metallic tone or ring. If it sounds cracked or dead, do not use it. The general industry rule adds that the spindle speed of the machine has to be checked before mounting the wheel to be certain it does not exceed the maximum operating speed marked on the wheel.

Next, the guard. The construction rule says the guard covers the spindle end, nut and flange projections, and it limits how much of the wheel is exposed. For bench and floor stands, the exposure is not more than 90 degrees, or one-fourth of the periphery. On portable grinders, the guard goes between the wheel and you. Taking it off to fit in a tight spot is one of the most common ways people get hurt.

Then the start-up. OSHA's booklet says to let the tool come up to operating speed before grinding or cutting, and to never stand directly in the plane of rotation of the wheel as it accelerates.

A few field habits for leaders to enforce. Match the wheel to the tool and the job. A cutoff wheel is not for side grinding. Check the wheel's speed rating against the tool. Replace wheels that are chipped, worn down past the manufacturer's limit, or dropped. Eye and face protection on every grind, with a face shield over safety glasses for cutoff work. And think about where the sparks go. On a live data center floor or a finished building, sparks can trigger detection systems or start fires, so follow the site's hot work rules.

Leader notes: Before the talk, collect the grinders and wheels on site. Show the speed marking on a wheel and the RPM on a tool's nameplate, and have the crew compare them. Demonstrate the ring test on a bench wheel. Check that every guard is present and positioned. Follow your site's procedure and the manufacturer's instructions.

Key points

  • Inspect and ring-test wheels before mounting
  • Wheel speed rating must not be exceeded by the spindle speed
  • Guards stay on and positioned between you and the wheel
  • Let it reach speed; stand out of the plane of rotation

Ask the crew

  1. Where do you find the maximum speed on the wheels we use?
  2. Why is a dropped wheel a risk even if it looks fine?

Check it today

Every grinder on site has its guard installed, and its wheels are rated at or above the tool's RPM.

Where this comes from

Get all 12 talk packs free
Want a full year of talks like this? The 52-week packs are free. Running a crew? The Foreman Membership adds all 108 one-page trackers and the Foreman training track for $19 a month.
Emergency & First AidSeptember sample

First Aid on Site: The First Few Minutes

When someone is badly hurt, help in the first few minutes matters. Who is first-aid trained on this job?

Read the talk

Today's Leader's Talk is about the first few minutes after someone gets badly hurt, and who on this job can help during them.

The construction rule on medical services and first aid starts with a simple idea. If there is no infirmary, clinic, hospital or physician reasonably accessible to the job, a person with valid first aid training has to be available at the worksite to give first aid. That training has to be documented.

What does reasonably accessible mean? The federal job safety agency has explained it in letters of interpretation. Where life-threatening injuries like severe bleeding or suffocation can be expected, it has said a 3 to 4 minute response time is required. Where a life-threatening injury is an unlikely outcome, a longer response time of up to 15 minutes may be acceptable. Think about our work: energized equipment, power tools, heights, and heavy material. Life-threatening injuries are possible on most of our jobs. And very few job sites have an ambulance that can reach a worker inside a building within 3 to 4 minutes.

That is why trained people on site matter so much. It is also why the rule requires a way to get help: equipment to transport an injured person to a doctor or hospital, or a communication system to contact an ambulance.

Here is what every person on this crew should know today. Who on our crew, and on this site, is first aid trained. Where the first aid kit is. Where the nearest eyewash is. How to call for help, and the address and gate responders should use. And who meets responders and walks them in.

The common mistake is assuming someone else is trained. Another is the one trained person always being on a different floor, or on vacation, or both.

Leader notes: Before this talk, find out who is first aid trained on your crew and when their training expires. If you do not have coverage on every shift and every area, raise it with your safety lead today. Name the trained people out loud during the talk so the crew knows who to call. Add a "first aid coverage" line to your pre-task plan so it gets checked every day, not just in September. Follow your site's emergency procedure and medical plan.

Key points

  • Without nearby medical care, a first aid trained person must be on site
  • Interpretations call for a 3 to 4 minute response where life-threatening injury is possible
  • Know who is trained, where the kit is, and how to call for help
  • Someone must meet responders and walk them in

Ask the crew

  1. Who on this crew is first aid trained, and are they here today?
  2. How long would it really take an ambulance to reach someone on the top floor of this job?

Check it today

The foreman names the first aid trained person on site today and where they are working.

Where this comes from

Get all 12 talk packs free
Want a full year of talks like this? The 52-week packs are free. Running a crew? The Foreman Membership adds all 108 one-page trackers and the Foreman training track for $19 a month.
Energy ControlOctober sample

Lockout and Tagout: The Six Steps in Order

Lockout is not just hanging a lock. The rule lists six steps, in order. Can your crew name them?

Read the talk

Today's Leader's Talk starts our lockout and tagout deep dive. For electrical crews, this is the procedure that stands between us and a circuit we thought was dead.

The federal general industry rule on the control of hazardous energy lists the steps of an energy control procedure and says they shall be done in this sequence.

One, preparation for shutdown. Before you turn anything off, the authorized person needs to know the type and amount of energy, the hazards, and how to control them. For us, that means drawings, single-lines, labels and a walkdown, not memory.

Two, machine or equipment shutdown. Shut it down using the normal stopping procedure, so you are not creating a new hazard by opening a disconnect under load.

Three, isolation. Operate every energy-isolating device needed to isolate the equipment from its energy sources. On electrical gear, think about every source: normal power, emergency power, generators, UPS outputs, control power from another panel, and backfeed.

Four, application of lockout or tagout devices. Each authorized person applies their own device to each isolating device.

Five, stored energy. After the devices are applied, all potentially hazardous stored or residual energy has to be relieved, disconnected, restrained or otherwise made safe.

Six, verification. Before starting work, verify the equipment is actually isolated and de-energized. For electrical work, that means testing for absence of voltage with a properly rated and checked tester.

For construction, the electrical rule adds its own requirements: controls to be deactivated during the work have to be tagged, deenergized equipment and circuits have to be rendered inoperative and have tags attached at all points where they can be energized, and tags have to plainly identify the equipment or circuits being worked on.

The most common failure is skipping step one. People jump straight to hanging locks on the disconnect they think is right, without confirming every source.

Leader notes: Have your site's written energy control procedure in hand during this talk and show the crew where the equipment-specific steps live. Ask a crew member to walk through the six steps for a real piece of equipment on this job. Make sure every authorized person has their own lock and knows it is theirs alone. This week, observe one lockout from start to finish and coach on what you see. Follow your site's procedure and the facility's procedure in live environments.

Key points

  • Six steps: prepare, shut down, isolate, lock and tag, relieve stored energy, verify
  • Identify every source, including backfeed and control power
  • Each authorized person applies their own device
  • Construction circuits must be rendered inoperative and tagged at every point of energization

Ask the crew

  1. What are all the energy sources feeding the equipment we are working on this week?
  2. Which of the six steps is easiest to skip, and why?

Check it today

A crew member walks the foreman through the six steps for a specific piece of equipment on this job.

Where this comes from

Get all 12 talk packs free
Want a full year of talks like this? The 52-week packs are free. Running a crew? The Foreman Membership adds all 108 one-page trackers and the Foreman training track for $19 a month.
Material Handling & RiggingNovember sample

Big Pull Day: Planning a Cable Pull

Feeder pull today? Plan it like a lift: equipment, positions, communication. Leader's Talk on cable pulling.

Read the talk

Cable pulls are one of the most physical things electricians do. Long runs of big feeders in a data center, service entrance conductors in a commercial building, medium-voltage cable through a duct bank. A big pull takes a crew working together like a lift crew, and it deserves a plan like a lift.

OSHA's electrical contractor guidance on pulling and feeding wire lists the hazards. Larger gauge wire takes more effort. Small diameter conduit adds resistance. Bends in the conduit raise the pulling force. Large, heavy spools make unwinding strenuous. Long runs mean repeated forceful exertion. Working from ladders twists the torso. Reaching overhead can restrict blood flow and compress nerves, causing numbness, tingling and fatigue.

The solutions are the plan. Use a mechanical wire puller, which can supply the force of several workers. Use portable pulleys so workers can pull with elbows close to the body and the torso upright. Put spools on spool rollers so wire comes off without twisting. Use lubricant where the wire enters conduit, chases or knockouts to cut friction. Use pull boxes at intervals to avoid long runs with lots of bends. Work from platforms, scaffolds or lifts instead of reaching off a ladder, and use platform ladders over regular ladders where you can. When pulling by hand, take regular breaks, rotate between pulling, feeding and other tasks, and wear gloves that improve grip.

Now add the parts that make it a crew operation. Who is running the puller? Who is feeding? Who is at each pull point? How do they talk to each other when they cannot see each other? Radios, phones, or a person relaying. Agree on a stop word or signal before you start, and agree that anyone can use it. When a pull binds, nobody yanks harder. You stop, figure out why, and fix it.

Set up the puller per the manufacturer's instructions, anchored the way it is designed to be. Stay out of the line of the pull rope where you can, in case something lets go. And keep the feed end clear so the feeder is not tripping on scraps and cord.

Leader notes: For the next big pull on the schedule, hold the pre-task plan at the feed end with everyone involved. Assign positions by name. Test the radios. Say the stop word out loud. Walk the route from the feed end to the puller. After the pull, ask the crew what made it hard and what we should change for the next one, and write it down.

Key points

  • Use mechanical pullers, pulleys and spool rollers to cut manual force
  • Lubricate and use pull points to reduce friction and bends
  • Work from platforms or lifts instead of reaching off ladders
  • Assign positions, test communication and agree on a stop signal
  • When a pull binds, stop and find out why

Ask the crew

  1. How will the feed end talk to the puller end on our next pull?
  2. What made our last pull harder than it needed to be?

Check it today

The next scheduled cable pull has a written plan naming positions, the communication method and the stop signal.

Where this comes from

Get all 12 talk packs free
Want a full year of talks like this? The 52-week packs are free. Running a crew? The Foreman Membership adds all 108 one-page trackers and the Foreman training track for $19 a month.
Leadership & CultureDecember sample

Stop-Work Authority: What It Is and How We Back It

Anyone on this crew can stop work they believe is unsafe. Leaders, today is about how we make that real.

Read the talk

This month we talk a lot about leadership. Let's start with the most important thing a leader can hand a crew: the confidence to stop the work.

OSHA's recommended practices on worker participation say workers should be empowered to request a temporary suspension or shutdown of any work activity they believe is unsafe. They also say workers should be able to raise concerns without retaliation, and that retaliation against workers is illegal under Section 11(c) of the OSH Act.

There is also a narrower legal protection worth knowing about. Under the OSHA rule on employee rights, a worker who refuses in good faith to do a task can be protected when they reasonably believe there is a real danger of death or serious injury, there is no reasonable alternative, there is not enough time to fix it through normal channels, and, where possible, they have asked the employer to correct it. That is the legal floor. Our stop-work authority is meant to be much broader and easier than that. This is not legal advice, and your company's stop-work procedure is what you follow.

So what does stop work look like on our jobs? Anyone can call it, on anything they believe is unsafe. You say stop, the work pauses, and everyone involved gets together. We look at what was seen, fix it or decide it is fine, and then restart. Nobody gets in trouble for calling stop in good faith, even if it turns out to be nothing.

Here is the hard part. Stop work is easy to write and hard to live. People will not use it if the last person who did got rolled eyes, a sigh from the foreman, or a comment about the schedule. The project manager's face when the crane stops for twenty minutes is a powerful thing. That is why leaders have to protect it every single time.

What does protecting it look like? Thank people out loud when they call stop. Ask questions before you judge. Follow up and tell them what changed. And call it yourself when you see something, so the crew sees it is normal.

Leader notes: Ask the crew today, honestly, whether they feel they can stop work. If anyone hesitates, ask why and listen without arguing. Tell a short story about a time you stopped work, or wish you had. Make sure the crew knows the exact words or signal we use. Then the next time someone calls stop, thank them in front of the whole crew, even if it turns out to be nothing.

Key points

  • Workers should be empowered to pause any work they believe is unsafe
  • Retaliation for raising safety concerns is illegal under Section 11(c)
  • Calling stop in good faith never gets anyone in trouble
  • Leaders protect stop work by thanking, asking and following up
  • Leaders call stop themselves so it feels normal

Ask the crew

  1. What would make someone on this job hesitate to call stop?
  2. What exact words or signal do we use to stop work here?

Check it today

Every crew member can state the words or signal used to stop work on this job.

Where this comes from

Get all 12 talk packs free
Want a full year of talks like this? The 52-week packs are free. Running a crew? The Foreman Membership adds all 108 one-page trackers and the Foreman training track for $19 a month.

The full library

A talk for every day of the year

Cold stress in January, electrical safety in February, ladders and lifts in March, fall protection in May, heat in June, trenching in July, lockout in October, rigging and cable pulls in November. Every Monday is a longer Leader's Talk with notes for the person running it.

Free talks, paid tools

  • Talk packs, free: every 52-week trade pack, bilingual and Leader's Talks, sent to your email
  • Foreman Membership, $19 a month: all 108 one-page trackers and the Foreman training track
  • General Foreman Membership, $29 a month: adds the full workbooks and planning kits
  • Superintendent Membership, $39 a month: the Complete Field Library
  • Crew Membership, $199 a month: Foreman Membership access for up to 15 people
  • Company Membership: 10+ field leaders from $15 a seat